Serving North and South Carolina

Emergency service available

(864) 706-9511

Service

Hydro Excavation

Pressurized water and vacuum, instead of a bucket and hope.

Protect What's Below.

Hydro excavation is a precise, non-mechanical digging method that uses pressurized water to loosen soil while a powerful vacuum removes the resulting material into a debris tank. This controlled process reduces the risk of damaging underground utilities and minimizes disturbance to the surrounding area.

The difference from a backhoe is not care, it is physics. A steel bucket cannot tell soil from a fiber conduit until it has already cut through one. Water can: it erodes soil and stops dead at anything solid. That is why utility owners, engineers and general contractors specify it over congested corridors, and why it is the only method most gas and electric companies will allow within a set distance of their own lines.

A steel bucket cannot tell soil from a fiber conduit until it has already cut through one. Water can.

Carolina Hydrovac is your solution for any situation where safe, accurate excavation is essential.

Applications include but are not limited to:

  • Utility potholing and daylighting
  • Slot trenching
  • Bollard, pole and sign holes
  • Water, sewer and storm repair excavation
  • Bore-entry and receiving pits
  • Valve, meter and hydrant exposure and cleaning
  • Test pits and subsurface investigations
  • Excavation around congested utilities
  • Commercial, municipal and industrial support

How a hydrovac dig actually runs

  1. 01

    Locate first

    Public 811 tickets get called, and anything private gets located before a hose comes off the reel. Hydro excavation is forgiving of a missed line — it will not cut one — but knowing what is down there decides where the hole goes.

  2. 02

    Cut with water

    A handheld wand delivers a narrow, high-pressure stream that breaks the soil into slurry. The operator controls depth by how long the stream sits in one place, which is why the method works within inches of a live line.

  3. 03

    Lift with vacuum

    A boom-mounted vacuum hose pulls the slurry straight into the debris tank as it forms. The spoil never sits on the ground, so there is no pile to trip over, wash into a drain, or shovel back.

  4. 04

    Expose and verify

    The line comes up clean and undamaged, at a measurable depth, with its coating intact. Photograph it, record the depth, and the design or the tie-in proceeds against a fact instead of an as-built.

  5. 05

    Leave it right

    Backfill, compact, and haul the spoil off. A hydrovac hole is small and its edges are intact, so restoration is a fraction of what an open-cut trench costs to put back.

Where it earns its cost

Congested corridors

Where four utilities share a right-of-way and the as-builts disagree with each other, mechanical digging is a coin flip. This is the situation hydro excavation was invented for.

Frozen or hard ground

Hot water cuts ground that a bucket has to be beaten into. Winter work in the Upstate rarely stops for the weather.

Restoration you have to pay for

A 12-inch pothole through a parking lot costs a patch. A trench costs a saw cut, a base repair and a stripe. On finished surfaces the excavation method is usually the cheaper half of the decision.

Tight or awkward access

The truck stays on the road and the hose reaches the work — behind a building, over a fence line, inside a live plant, next to something you cannot put a track machine beside.

Around roots and structures

Water strips soil off a root ball or a footing without cutting either. Tree preservation and foundation investigation both depend on that.

Common questions

About hydro excavation

What is hydro excavation?

Digging with pressurized water and a vacuum instead of a mechanical bucket. A handheld wand cuts the soil into slurry and a boom-mounted hose lifts it straight into a debris tank on the truck. Because nothing solid ever enters the hole, the method can work within inches of a live utility without damaging it. It is also called vacuum excavation, soft digging, or — when the goal is simply to see a line — daylighting or potholing.

Why not just use a backhoe?

Because a bucket cannot detect a utility, it can only find one. On open ground with nothing underneath it, mechanical excavation is faster and cheaper and you should use it. The calculation changes when there is live line in the hole, when the surface above has to be put back, or when the ground is stiff Piedmont clay that a machine has to fight. Then the slower cut is usually the cheaper job once restoration and risk are in the number.

How deep can you dig?

Depth is limited by hose length and by what the soil does as the hole gets deeper, not by the method. Typical utility work — potholing, service exposure, bore pits — sits comfortably in the range hydro excavation is built for. Anything unusually deep is worth describing on the phone first so you get a straight answer about whether it suits the method.

Does it work in frozen or hard ground?

Yes, and it is one of the method's better arguments. Hot water cuts ground that a mechanical bucket has to be beaten into. Upstate winters rarely freeze deep, but stiff, dry clay behaves much the same way, and water handles both.

What happens to the material that comes out?

It goes into the debris tank as it is cut and leaves on the truck. Nothing is stockpiled beside the hole, which matters on a live site, on finished pavement, and anywhere with a stormwater plan that does not allow a spoil pile next to an inlet.

What if the work is somewhere a truck cannot reach?

The truck does not have to reach it — the hose does. That is a large part of why the method gets specified inside plants, behind buildings, over fence lines and on sites where there is nowhere to put a track machine.

Have a job that needs hydro excavation?

Tell us where it is and what is in the way. Photographs and a site plan get you a far more accurate number.